MIT engineers design surfaces that make water boil more efficiently

The boiling of water or other fluids is an energy-intensive step at the heart of a wide range of industrial processes, including most electricity generating plants, many chemical production systems, and even cooling systems for electronics.

Improving the efficiency of systems that heat and evaporate water could significantly reduce their energy use. Now, researchers at MIT have found a way to do just that, with a specially tailored surface treatment for the materials used in these systems.

The improved efficiency comes from a combination of three different kinds of surface modifications, at different size scales. The new findings are described in the journal Advanced Materials in a paper by recent MIT graduate Youngsup Song PhD '21, Ford Professor of Engineering Evelyn Wang, and four others at MIT. The researchers note that this initial finding is still at a laboratory scale, and more work is needed to develop a practical, industrial-scale process.

There are two key parameters that describe the boiling process: the heat transfer coefficient (HTC) and the critical heat flux (CHF). In materials design, there's generally a tradeoff between the two, so anything that improves one of these parameters tends to make the other worse. But both are important for the efficiency of the system, and now, after years of work, the team has achieved a way of significantly improving both properties at the same time, through their combination of different textures added to a material's surface.

"Both parameters are important," Song says, "but enhancing both parameters together is kind of tricky because they have intrinsic trade off." The reason for that, he explains, is "because if we have lots of bubbles on the boiling surface, that means boiling is very efficient, but if we have too many bubbles on the surface, they can coalesce together, which can form a vapor film over the boiling surface."

That film introduces resistance to the heat transfer from the hot surface to the water. "If we have vapor in between the surface and water, that prevents the heat transfer efficiency and lowers the CHF value," he says.

Song, who is now a postdoc at Lawrence Berkeley National Laboratory, carried out much of the research as part of his doctoral thesis work at MIT. While the various components of the new surface treatment he developed had been previously studied, the researchers say this work is the first to show that these methods could be combined to overcome the tradeoff between the two competing parameters.

Adding a series of microscale cavities, or dents, to a surface is a way of controlling the way bubbles form on that surface, keeping them effectively pinned to the locations of the dents and preventing them from spreading out into a heat-resisting film. In this work, the researchers created an array of 10-micrometer-wide dents separated by about 2 millimeters to prevent film formation. But that separation also reduces the concentration of bubbles at the surface, which can reduce the boiling efficiency.

To compensate for that, the team introduced a much smaller-scale surface treatment, creating tiny bumps and ridges at the nanometer scale, which increases the surface area and promotes the rate of evaporation under the bubbles.

In these experiments, the cavities were made in the centers of a series of pillars on the material's surface. These pillars, combined with nanostructures, promote wicking of liquid from the base to their tops, and this enhances the boiling process by providing more surface area exposed to the water. In combination, the three "tiers" of the surface texture - the cavity separation, the posts, and the nanoscale texturing - provide a greatly enhanced efficiency for the boiling process, Song says.

"Those micro cavities define the position where bubbles come up," he says. "But by separating those cavities by 2 millimeters, we separate the bubbles and minimize the coalescence of bubbles." At the same time, the nanostructures promote evaporation under the bubbles, and the capillary action induced by the pillars supplies liquid to the bubble base. That maintains a layer of liquid water between the boiling surface and the bubbles of vapor, which enhances the maximum heat flux.

Although their work has confirmed that the combination of these kinds of surface treatments can work and achieve the desired effects, this work was done under small-scale laboratory conditions that could not easily be scaled up to practical devices, Wang says. "These kinds of structures we're making are not meant to be scaled in its current form," she says, but rather were used to prove that such a system can work. One next step will be to find alternative ways of creating these kinds of surface textures so these methods could more easily be scaled up to practical dimensions.

"Showing that we can control the surface in this way to get enhancement is a first step," she says. "Then the next step is to think about more scalable approaches." For example, though the pillars on the surface in these experiments were created using clean-room methods commonly used to produce semiconductor chips, there are other, less demanding ways of creating such structures, such as electrodeposition. There are also a number of different ways to produce the surface nanostructure textures, some of which may be more easily scalable.

There may be some significant small-scale applications that could use this process in its present form, such as the thermal management of electronic devices, an area that is becoming more important as semiconductor devices get smaller and managing their heat output becomes ever more important. "There's definitely a space there where this is really important," Wang says.

Even those kinds of applications will take some time to develop because typically thermal management systems for electronics use liquids other than water, known as dielectric liquids. These liquids have different surface tension and other properties than water, so the dimensions of the surface features would have to be adjusted accordingly. Work on these differences is one of the next steps for the ongoing research, Wang says.

This same multiscale structuring technique could also be applied to different liquids, Song says, by adjusting the dimensions to account for the different properties of the liquids. "Those kinds of details can be changed, and that can be our next step," he says.

hree-tier hierarchical structures for extreme pool boiling heat transfer performance"

Research Report:"Three-tier hierarchical structures for extreme pool boiling heat transfer performance"

Related Links
Device Research Laboratory
Space Technology News - Applications and Research

Tweet

Thanks for being there;
We need your help. The SpaceDaily news network continues to grow but revenues have never been harder to maintain.

With the rise of Ad Blockers, and Facebook - our traditional revenue sources via quality network advertising continues to decline. And unlike so many other news sites, we don't have a paywall - with those annoying usernames and passwords.

Our news coverage takes time and effort to publish 365 days a year.

If you find our news sites informative and useful then please consider becoming a regular supporter or for now make a one off contribution.

SpaceDaily Monthly Supporter
$5+ Billed Monthly

paypal only

SpaceDaily Contributor
$5 Billed Once

credit card or paypal

Chinese ice cream brand under fire for products that don't melt
Beijing (AFP) July 7, 2022
A Chinese brand once dubbed the "Hermes of ice cream" has come under fire after internet users said some of its products do not melt - even when baked with a blowtorch. Videos showing Chicecream's ice creams staying solid when lighters were held to them went viral, revealing they did not fully melt when left in a 31 degree Celsius (88 degree Fahrenheit) room for an hour or under a very hot flame. The footage sparked consternation online, prompting users to question the company's high prices and ... read more