24/7 Space News
TECH SPACE
Scientists 3D print self-heating microfluidic devices
MIT researchers developed a fabrication process to produce self-heating microfluidic devices in one step using a multi-material 3D printer. Pictured is an example of one of the devices.
Scientists 3D print self-heating microfluidic devices
by Adam Zewe | MIT News
Boston MA (SPX) Dec 12, 2023

MIT researchers have used 3D printing to produce self-heating microfluidic devices, demonstrating a technique which could someday be used to rapidly create cheap, yet accurate, tools to detect a host of diseases.

Microfluidics, miniaturized machines that manipulate fluids and facilitate chemical reactions, can be used to detect disease in tiny samples of blood or fluids. At-home test kits for Covid-19, for example, incorporate a simple type of microfluidic.

But many microfluidic applications require chemical reactions that must be performed at specific temperatures. These more complex microfluidic devices, which are typically manufactured in a clean room, are outfitted with heating elements made from gold or platinum using a complicated and expensive fabrication process that is difficult to scale up.

Instead, the MIT team used multimaterial 3D printing to create self-heating microfluidic devices with built-in heating elements, through a single, inexpensive manufacturing process. They generated devices that can heat fluid to a specific temperature as it flows through microscopic channels inside the tiny machine.

Their technique is customizable, so an engineer could create a microfluidic that heats fluid to a certain temperature or given heating profile within a specific area of the device. The low-cost fabrication process requires about $2 of materials to generate a ready-to-use microfluidic.

The process could be especially useful in creating self-heating microfluidics for remote regions of developing countries where clinicians may not have access to the expensive lab equipment required for many diagnostic procedures.

"Clean rooms in particular, where you would usually make these devices, are incredibly expensive to build and to run. But we can make very capable self-heating microfluidic devices using additive manufacturing, and they can be made a lot faster and cheaper than with these traditional methods. This is really a way to democratize this technology," says Luis Fernando Velasquez-Garcia, a principal scientist in MIT's Microsystems Technology Laboratories (MTL) and senior author of a paper describing the fabrication technique.

He is joined on the paper by lead author Jorge Canada Perez-Sala, an electrical engineering and computer science graduate student. The research will be presented at the PowerMEMS Conference this month.

An insulator becomes conductive
This new fabrication process utilizes a technique called multimaterial extrusion 3D printing, in which several materials can be squirted through the printer's many nozzles to build a device layer by layer. The process is monolithic, which means the entire device can be produced in one step on the 3D printer, without the need for any post-assembly.

To create self-heating microfluidics, the researchers used two materials - a biodegradable polymer known as polylactic acid (PLA) that is commonly used in 3D printing, and a modified version of PLA.

The modified PLA has mixed copper nanoparticles into the polymer, which converts this insulating material into an electrical conductor, Velasquez-Garcia explains. When electrical current is fed into a resistor composed of this copper-doped PLA, energy is dissipated as heat.

"It is amazing when you think about it because the PLA material is a dielectric, but when you put in these nanoparticle impurities, it completely changes the physical properties. This is something we don't fully understand yet, but it happens and it is repeatable," he says.

Using a multimaterial 3D printer, the researchers fabricate a heating resistor from the copper-doped PLA and then print the microfluidic device, with microscopic channels through which fluid can flow, directly on top in one printing step. Because the components are made from the same base material, they have similar printing temperatures and are compatible.

Heat dissipated from the resistor will warm fluid flowing through the channels in the microfluidic.

In addition to the resistor and microfluidic, they use the printer to add a thin, continuous layer of PLA that is sandwiched between them. It is especially challenging to manufacture this layer because it must be thin enough so heat can transfer from the resistor to the microfluidic, but not so thin that fluid could leak into the resistor.

The resulting machine is about the size of a U.S. quarter and can be produced in a matter of minutes. Channels about 500 micrometers wide and 400 micrometers tall are threaded through the microfluidic to carry fluid and facilitate chemical reactions.

Importantly, the PLA material is translucent, so fluid in the device remains visible. Many processes rely on visualization or the use of light to infer what is happening during chemical reactions, Velasquez-Garcia explains.

Customizable chemical reactors
The researchers used this one-step manufacturing process to generate a prototype that could heat fluid by 4 degrees Celsius as it flowed between the input and the output. This customizable technique could enable them to make devices which would heat fluids in certain patterns or along specific gradients.

"You can use these two materials to create chemical reactors that do exactly what you want. We can set up a particular heating profile while still having all the capabilities of the microfluidic," he says.

However, one limitation comes from the fact that PLA can only be heated to about 50 degrees Celsius before it starts to degrade. Many chemical reactions, such as those used for polymerase chain reaction (PCR) tests, require temperatures of 90 degrees or higher. And to precisely control the temperature of the device, researchers would need to integrate a third material that enables temperature sensing.

In addition to tackling these limitations in future work, Velasquez-Garcia wants to print magnets directly into the microfluidic device. These magnets could enable chemical reactions that require particles to be sorted or aligned.

At the same time, he and his colleagues are exploring the use of other materials that could reach higher temperatures. They are also studying PLA to better understand why it becomes conductive when certain impurities are added to the polymer.

"If we can understand the mechanism that is related to the electrical conductivity of PLA, that would greatly enhance the capability of these devices, but it is going to be a lot harder to solve than some other engineering problems," he adds.

"In Japanese culture, it's often said that beauty lies in simplicity. This sentiment is echoed by the work of Canada and Velasquez-Garcia. Their proposed monolithically 3D-printed microfluidic systems embody simplicity and beauty, offering a wide array of potential derivations and applications that we foresee in the future," says Norihisa Miki, a professor of mechanical engineering at Keio University in Tokyo, who was not involved with this work.

"Being able to directly print microfluidic chips with fluidic channels and electrical features at the same time opens up very exiting applications when processing biological samples, such as to amplify biomarkers or to actuate and mix liquids. Also, due to the fact that PLA degrades over time, one can even think of implantable applications where the chips dissolve and resorb over time," adds Niclas Roxhed, an associate professor at Sweden's KTH Royal Institute of Technology, who was not involved with this study.

This research was funded, in part, by the Empiriko Corporation and a fellowship from La Caixa Foundation.

Related Links
Microsystems Technology Laboratories
Space Technology News - Applications and Research

Subscribe Free To Our Daily Newsletters
Tweet

RELATED CONTENT
The following news reports may link to other Space Media Network websites.
TECH SPACE
WVU research advances 3D printing applications in microgravity for sustainable space missions
Morgantown WV (SPX) Oct 31, 2023
Research from West Virginia University students and faculty into how 3D printing works in a weightless environment aims to support long-term exploration and habitation on spaceships, the moon or Mars. Extended missions in outer space require the manufacture of crucial materials and equipment onsite, rather than transporting those items from Earth. ... read more

TECH SPACE
NASA Outlines Future Strategy for Post-ISS Microgravity Research Labs in LEO

Jeff Bezos's Blue Origin headed back into space after accident

NASA: Let's Ketchup on International Space Station Tomato Research

NASA's Commercial Partners Continue Progress on New Space Stations

TECH SPACE
Virgin Galactic sets January 2024 for 11th mission

NASA's 3D-printed Rotating Detonation Rocket Engine Test a Success

Sierra Space's Dream Chaser New Station Resupply Spacecraft for NASA

Blue Origin scrubs return of New Shepard rocket flight due to technical issue

TECH SPACE
Recent volcanism on Mars reveals a planet more active than previously thought

Sussex research takes us a step closer to sustaining human life on Mars

A Soliday Before the Holidays Sols 4039-4040

Rocker-Bogie Around the Marsmas Sea: Sols 4041-4042

TECH SPACE
China's space programme: Five things to know

Shenzhou XVII astronauts set for their first spacewalk

China's commercial space sector achieves milestones with series of successful launches

Long March rockets mark their 500th spaceflight

TECH SPACE
Bayanat and Yahsat to Merge, Forming AI-Driven Space Technology Powerhouse, Space42

NASA Enhances Aerospace Innovation with New SBIR Ignite Phase I Awards

NASA and Blue Origin partner to propel space technology in latest suborbital flight

Satellite Communications Innovator Lynk Global to Go Public via Slam Corp. Merger

TECH SPACE
A computer scientist pushes the boundaries of geometry

The feline frontier: NASA sends cat video from deep space

Sidus Space's LizzieSat gears up for launch with successful test

Scientists 3D print self-heating microfluidic devices

TECH SPACE
Astrophysicists publish Kepler Giant Planet Search, an aid to 'figure out where to find life'

Earth may have had all the elements needed for life within it all along

NEOWISE space telescope marks 10 Years on orbit as End of Mission looms

NASA Study Finds Life-Sparking Energy Source and Molecule at Enceladus

TECH SPACE
The PI's Perspective: The Long Game

Webb rings in the holidays with the ringed planet Uranus

Unwrapping Uranus and its icy moon secrets

Juice burns hard towards first-ever Earth-Moon flyby

Subscribe Free To Our Daily Newsletters




The content herein, unless otherwise known to be public domain, are Copyright 1995-2024 - Space Media Network. All websites are published in Australia and are solely subject to Australian law and governed by Fair Use principals for news reporting and research purposes. AFP, UPI and IANS news wire stories are copyright Agence France-Presse, United Press International and Indo-Asia News Service. ESA news reports are copyright European Space Agency. All NASA sourced material is public domain. Additional copyrights may apply in whole or part to other bona fide parties. All articles labeled "by Staff Writers" include reports supplied to Space Media Network by industry news wires, PR agencies, corporate press officers and the like. Such articles are individually curated and edited by Space Media Network staff on the basis of the report's information value to our industry and professional readership. Advertising does not imply endorsement, agreement or approval of any opinions, statements or information provided by Space Media Network on any Web page published or hosted by Space Media Network. General Data Protection Regulation (GDPR) Statement Our advertisers use various cookies and the like to deliver the best ad banner available at one time. All network advertising suppliers have GDPR policies (Legitimate Interest) that conform with EU regulations for data collection. By using our websites you consent to cookie based advertising. If you do not agree with this then you must stop using the websites from May 25, 2018. Privacy Statement. Additional information can be found here at About Us.