Form fit: Device wraps around hot surfaces, turns wasted heat to electricity

The energy systems that power our lives also produce wasted heat - like heat that radiates off hot water pipes in buildings and exhaust pipes on vehicles. A new flexible thermoelectric generator can wrap around pipes and other hot surfaces and convert wasted heat into electricity more efficiently than previously possible, according to scientists at Penn State and the National Renewable Energy Laboratory.

"A large amount of heat from the energy we consume is essentially being thrown away, often dispersed right into the atmosphere," said Shashank Priya, associate vice president for research and professor of materials science and engineering at Penn State. "We haven't had cost-effective ways with conformal shapes to trap and convert that heat to useable energy. This research opens that door."

Penn State researchers have been working to improve the performance of thermoelectric generators - devices that can convert differences in temperature to electricity. When the devices are placed near a heat source, electrons moving from the hot side to the cold side produce an electric current, the scientists said.

In prior work, the team created rigid devices that were more efficient than commercial units in high-temperature applications. Now the team has developed a new manufacturing process to produce flexible devices that offer higher power output and efficiency, the scientists said.

"These results provide a promising pathway toward widespread utilization of thermoelectric technology into waste heat recovery application," said Wenjie Li, assistant research professor at Penn State. "This could have a significant impact on the development of practical thermal to electrical generators."

Flexible devices better fit the most attractive waste heat sources, like pipes in industrial and residential buildings and on vehicles, the scientists said. And they don't have to be glued on surfaces like traditional, rigid devices, which further decreases efficiency.

In tests being conducted on a gas flue, the new device exhibited 150% higher power density than other state-of-the-art units, the scientists reported in Applied Materials and Interfaces. A scaled-up version, just over 3-inches squared, maintained a 115% power density advantage. That version exhibited a total power output of 56.6 watts when placed on the hot surface, the scientists said.

"Think about an industrial power plant with pipes hundreds of feet long," Priya said. "If you can wrap these devices around an area that large, you could generate kilowatts of energy from wasted heat that's normally just being thrown away. You could convert discarded heat into something useful."

Thermoelectric devices are made up of small couples, each resembling a table with two legs. Many of these two-leg couples are connected together, typically forming a flat, square device.

In creating the new device, scientists placed six couples along a thin strip. They then used flexible metal foil to connect 12 of the strips together, creating a device with 72 couples. Liquid metal was used between the layers of each strip to improve device performance, the scientist said.

"As you scale up these devices, you often lose power density, making it challenging to fabricate large-scale thermoelectric generators," said Bed Poudel, associate research professor at Penn State. "This illustrates the extraordinary performance of our 72-couple device."

The 72-couple device exhibited the highest reported output power and device power density from a single thermoelectric generator, the scientists said.

The gaps between the strips provide the flexibility to fit around shapes like pipes. The gaps also allow for flexibility in altering the fill factor, or the ratio between the area of thermoelectric material and the area of the device, which can be used to optimize thermoelectric devices for different heat sources, the scientists said.

Other Penn State researchers on the project were Amin Nozariasbmarz, assistant research professor; Han Byul Kang and Hangtain Zhu, postdoctoral researchers; and Carter Dettor, a former graduate student.

Ravi Anant Kishore, research engineer at National Renewable Energy Laboratory, also contributed.

Various authors contributing to this study were supported through Department of Energy, Office of Naval Research, Army Research Office, National Science Foundation and Defense Advanced Research Projects Agency.

Research Report: "Conformal High-Power-Density Half-Heusler Thermoelectric Modules: A Pathway toward Practical Power Generators"

Related Links
Penn State
Powering The World in the 21st Century at Energy-Daily.com

Tweet

Thanks for being there;
We need your help. The SpaceDaily news network continues to grow but revenues have never been harder to maintain.

With the rise of Ad Blockers, and Facebook - our traditional revenue sources via quality network advertising continues to decline. And unlike so many other news sites, we don't have a paywall - with those annoying usernames and passwords.

Our news coverage takes time and effort to publish 365 days a year.

If you find our news sites informative and useful then please consider becoming a regular supporter or for now make a one off contribution.

SpaceDaily Monthly Supporter
$5+ Billed Monthly

paypal only

SpaceDaily Contributor
$5 Billed Once

credit card or paypal

Redrawing the lines: Growing inexpensive, high-quality iron-based superconductors
Nagoya, Japan (SPX) Dec 20, 2021
Superconducting materials show zero electrical resistance at low temperatures, which allows them to conduct "supercurrents" without dissipation. Recently, a group of scientists led by Dr. Kazumasa Iida from Nagoya University, Japan, developed an inexpensive, scalable way to produce high-temperature superconductors using "grain boundary engineering" techniques. The new method could help develop stronger, inexpensive, and high operating temperature superconductors with impactful technological applications ... read more